PLEASE NOTE: In order to post on the Board you need to have registered. To register please email paul@sexyloops.com including your real name and username. Registration takes less than 24hrs, unless Paul is fishing deep in the jungle!
Braid for Snakehead.
Moderators: Viking Lars, Magnus
- Lasse Karlsson
- Posts: 5783
- Joined: Wed Jan 09, 2013 9:40 pm
- Location: There, and back again
- Contact:
Braid for Snakehead.
Thanks Graeme, with additiv right?
Cheers
Lasse
Cheers
Lasse
Your friendly neighbourhood flyslinger
Flycasting, so simple that instructors need to make it complicated since 1685
Got a Q++ at casting school, wearing shorts
Flycasting, so simple that instructors need to make it complicated since 1685
Got a Q++ at casting school, wearing shorts
Braid for Snakehead.
Yep, the additive is a little varnish.
Soak the leader in the mixture so that it penetrates throughout, then hang the leader to dry for three to four weeks.
Soak the leader in the mixture so that it penetrates throughout, then hang the leader to dry for three to four weeks.
FFi CCI
- Lasse Karlsson
- Posts: 5783
- Joined: Wed Jan 09, 2013 9:40 pm
- Location: There, and back again
- Contact:
Braid for Snakehead.
Hi Graeme
Have you tried viping the excess oil of after soaking it? Should cut down the drying time dramatically.
Are you hanging them outside? UV speeds up the drying time too.
The additive makes the oil dry faster, and turn it into a varnish, it also halts the penetration abilties of the oil. That hardly matters with braid though
Gotta try those leaders!
Cheers
Lasse
Have you tried viping the excess oil of after soaking it? Should cut down the drying time dramatically.
Are you hanging them outside? UV speeds up the drying time too.
The additive makes the oil dry faster, and turn it into a varnish, it also halts the penetration abilties of the oil. That hardly matters with braid though
Gotta try those leaders!
Cheers
Lasse
Your friendly neighbourhood flyslinger
Flycasting, so simple that instructors need to make it complicated since 1685
Got a Q++ at casting school, wearing shorts
Flycasting, so simple that instructors need to make it complicated since 1685
Got a Q++ at casting school, wearing shorts
Braid for Snakehead.
I know that dictum.com sells swedish raw, cold-bleached linseed oil. I guess that it is as low viscosity as in normal raw linseed oil, which is good for penetration. But it dries in 8 days instead of 3-4 weeks. Boiled linseed oil dries faster still, I think but has less penetration. I haven't used the cold-bleached oil but I think I will some day for wood at least, but maybe for leader making if I come to that.
https://www.dictum.com/en/oils-dbf/lino ... 1-l-705275
https://www.dictum.com/en/oils-dbf/lino ... 1-l-705275
Braid for Snakehead.
G'day Lasse,Lasse Karlsson wrote:Hi Graeme
Have you tried viping the excess oil of after soaking it? Should cut down the drying time dramatically.
Are you hanging them outside? UV speeds up the drying time too.
The additive makes the oil dry faster, and turn it into a varnish, it also halts the penetration abilties of the oil. That hardly matters with braid though
Gotta try those leaders!
Cheers
Lasse
Yes, I sometimes wipe off the oil, but not for the purpose of quicker drying. I do it only to modify the final weight of the leader.
That dried boiled linseed oil adds the desired mass to the braid, helping it match the mass distribution of the fly line. Wiping off too much will have a negative impact. For some leaders, I'll even put a second coating on all or part of it.
It's important to remember that the oil/varnish is not just something to protect the braid. The leader doesn't work without that ingredient. In silk fly lines, it provides mass in the same way that the PVC coating provides mass on modern fly lines.
Cheers,
Graeme
FFi CCI
- Lasse Karlsson
- Posts: 5783
- Joined: Wed Jan 09, 2013 9:40 pm
- Location: There, and back again
- Contact:
Braid for Snakehead.
Hi Graeme
I understood that it was to add weight and durability to the braid, its just that one normally wipes of excess oil when coating wood, because the excess prolongs the drying time significantly, and since you where drying yours for 3-4 weeks, I just wondered if that could be the reason
Cheers
Lasse
I understood that it was to add weight and durability to the braid, its just that one normally wipes of excess oil when coating wood, because the excess prolongs the drying time significantly, and since you where drying yours for 3-4 weeks, I just wondered if that could be the reason
Cheers
Lasse
Your friendly neighbourhood flyslinger
Flycasting, so simple that instructors need to make it complicated since 1685
Got a Q++ at casting school, wearing shorts
Flycasting, so simple that instructors need to make it complicated since 1685
Got a Q++ at casting school, wearing shorts
- Paul Arden
- Site Admin
- Posts: 19583
- Joined: Thu Jan 03, 2013 11:20 am
- Location: Belum Rainforest
- Contact:
Braid for Snakehead.
Yes that would be fantastic Lasse. I can send you a leader in exchangeLet me know if I can help...
Thanks, Paul
- Paul Arden
- Site Admin
- Posts: 19583
- Joined: Thu Jan 03, 2013 11:20 am
- Location: Belum Rainforest
- Contact:
Braid for Snakehead.
I use this address in Malaysia-
PAUL ARDEN
BANDARIANG ENGINEERING & CONSTRUCTION
NO 26A KAMPUNG BANDARIANG
C/O MONHD SAHRILL
GERIK PERAK
MALAYSIA 33320
PAUL ARDEN
BANDARIANG ENGINEERING & CONSTRUCTION
NO 26A KAMPUNG BANDARIANG
C/O MONHD SAHRILL
GERIK PERAK
MALAYSIA 33320
Braid for Snakehead.
Oh, I now see why this thread started up. I didn't realise there was a front page about these leaders. I guess it's even more important for me to make that video about them now.
I'll see what I can do over the weekend.
Cheers,
Graeme
I'll see what I can do over the weekend.
Cheers,
Graeme
FFi CCI
- Paul Arden
- Site Admin
- Posts: 19583
- Joined: Thu Jan 03, 2013 11:20 am
- Location: Belum Rainforest
- Contact:
Braid for Snakehead.
That would be great Graeme!
I’m making one now
Cheers, Paul
I’m making one now
Cheers, Paul